willllllieee
06-17-2007, 09:32 PM
Drive train
Sirio 23
JP-2 pipe
6 Clover SPI Racing Wheels anode pincheto green, one of a kind maid for me by rick at SPI Racing Wheels
Imex Claw dawg tires
Panther molded foams $
Ofna gun mettle fuel filter
Larger stone filter in tank
40 tooth spure
38 tooth spure
36 tooth spure
14 tooth ofna vented clutch bell. It was for a big block but i cut down the back of the bell so it fits the clutch perfectly.
15 tooth ofna vented clutch bell
13 tooth traxxas vented clutch bell
Ceramic Boca bearings
lightning siries bearings in the engine and tranny
gun mettle grey fule line all around , rare, hard to find
Close ratio gears in tranny
40 mm disk break
2 stock disk brakes, smaller diamiter, 1 new, one used
a coupld set of used brake shoes
kustom out put shaft, cnced from t-7075
Modified shift linkage
And an aluminum mount ontop of the tranny ( for the VSM),i set it all up but i din't hv to tim to caibrate it.
Ofna 3 piece air filter with stock traxxas revo neck
several other air filters includeing, gun mettle grey integy oen wiht new filter and screw off top, stock traxxas ones, and some more for the t-maxx that work fin
extra engine mount and header for the sirio 23 anodized orange
Suspension
Integy MSR6 shocks with kustom floats, and 30 pound springs 90, and 100 wt diff oil. red
integy MSR^ shocks, i haven't messed with them, just got them used, they have 60wt oil in them, they are blue
Integy long travel rockers
Long travel red tube pushrods
RPM a-arms died hunter green
Electronics
Twin battery mod, I am using two ofna 1600 mah batts
JR-XR2 radio with 4 crystals and 2 receivers (not both installed)
Venom Smart Temp/ fail safe/ volt monitor
Venom VSM, venom speed monitor
Other mods
Kustom front skid plate, i maid it out of aircraft grade aluminum, and plastic that i got from an rc snowmobile, it deflects rocks from axels nad works/looks tons better, also, it is lighter
Kustom mud guards or a-arm skids maid from aluminum. Pertects a-arms, and keeps suspension cleaner
Moded exhaust pipe, spray the inside with Teflon and the heat gets out of the pipe much better
Heavy servo saver
extra Integy skids
Kustom batterie box skid, it also pertects the gas tank
Integy roll bare
No rear bumper or bumper mount
i have rear bumper mount upside down, putting the bumper closer to the ground, pertecting the chassis better, looks better, and lowers center of gravity
Tekno wing mount
Ofna wing
Kustom mounted VSM, I have a plate maid up that sits on top the tranny for hte VSM
Kustom radio box, I shaved revo off the top, and I cut a hole in the bottom so I could mount the Smart Temp so I could see it with the body on. Also, I have a hole cut in the back for the heat probe that goes to the engine.
Sealed electronics
I cut the manifold and extended it with a silicone air filter neck form an Integy filter that was useless.
Lunsford TI hinge pins all around
Reamed the a-arms free so they would bind less
two Stainless steal screw kits
RPM bumper
Upside down front bumper mount( puts it lower to the ground and it sits on top of my kustom skid plate)
Aluminum wheel hexes
Steering stops are cut
Extended carbon fiber center skid plate
Boca series ceramic bearings in every thing except hubs
And my set up is
60 k diff fluid
90 wt oil in front shocks, 100 in the rear. Float with 3rd hole drilled in it for more flow
2 digress toe in on the front, 1 digress toe out in the rear.
Long travel rockers and tie-rods
Lowest slot in front and middle in the rear
Bodies
1 Pro-line Chevy Silverado HD Concept, painted by Tyson Heck at Total airbrush graphics
2 Pro-line Crowd Pleazer 2.0 painted by Tyson Heck at Total Airbrush Graphics
3 Grave digger body, painted flat black by me
4 Stock body painted by Traxxas
Sirio 23 monster power engine. 2 gallons ran. Still getting stronger. Has a scratch on the cooling head. All new bearings.
Engine new, comes with two mounts
boca lightning sires bearings
__________________________
TRX 2.5r
started life as a 2.5 tmaxx engine. I rebiult it wiht all new trx 2.5r engines, never started
3 chargers for rx battarie chargers.
duratrax charger
Tsais twin exhaust pipe
spare stearing servos x3
plus ALL extram skid plates, meaning i have everything plastic stock, and i also have enver used aluminum parts i didn't use. I have original rockers, a-arms, chassis parts, and new axels. Everything i ever bought for the truck exept a few engines, and tires comes with it. I used to run a werks 4 shoe racing clutch and i would recomend it if you ever race, but they requre cleaning ALL the time i also have alot of other parts to i probaly forget stuff but any more questions email me at patfatnu@hotmail.com i got lots of pics to i jsut dont know how to upl;oad them give offers in cash or trade ide liek a stock revo 3.3 or a tmaxx 3.3 and cash
Sirio 23
JP-2 pipe
6 Clover SPI Racing Wheels anode pincheto green, one of a kind maid for me by rick at SPI Racing Wheels
Imex Claw dawg tires
Panther molded foams $
Ofna gun mettle fuel filter
Larger stone filter in tank
40 tooth spure
38 tooth spure
36 tooth spure
14 tooth ofna vented clutch bell. It was for a big block but i cut down the back of the bell so it fits the clutch perfectly.
15 tooth ofna vented clutch bell
13 tooth traxxas vented clutch bell
Ceramic Boca bearings
lightning siries bearings in the engine and tranny
gun mettle grey fule line all around , rare, hard to find
Close ratio gears in tranny
40 mm disk break
2 stock disk brakes, smaller diamiter, 1 new, one used
a coupld set of used brake shoes
kustom out put shaft, cnced from t-7075
Modified shift linkage
And an aluminum mount ontop of the tranny ( for the VSM),i set it all up but i din't hv to tim to caibrate it.
Ofna 3 piece air filter with stock traxxas revo neck
several other air filters includeing, gun mettle grey integy oen wiht new filter and screw off top, stock traxxas ones, and some more for the t-maxx that work fin
extra engine mount and header for the sirio 23 anodized orange
Suspension
Integy MSR6 shocks with kustom floats, and 30 pound springs 90, and 100 wt diff oil. red
integy MSR^ shocks, i haven't messed with them, just got them used, they have 60wt oil in them, they are blue
Integy long travel rockers
Long travel red tube pushrods
RPM a-arms died hunter green
Electronics
Twin battery mod, I am using two ofna 1600 mah batts
JR-XR2 radio with 4 crystals and 2 receivers (not both installed)
Venom Smart Temp/ fail safe/ volt monitor
Venom VSM, venom speed monitor
Other mods
Kustom front skid plate, i maid it out of aircraft grade aluminum, and plastic that i got from an rc snowmobile, it deflects rocks from axels nad works/looks tons better, also, it is lighter
Kustom mud guards or a-arm skids maid from aluminum. Pertects a-arms, and keeps suspension cleaner
Moded exhaust pipe, spray the inside with Teflon and the heat gets out of the pipe much better
Heavy servo saver
extra Integy skids
Kustom batterie box skid, it also pertects the gas tank
Integy roll bare
No rear bumper or bumper mount
i have rear bumper mount upside down, putting the bumper closer to the ground, pertecting the chassis better, looks better, and lowers center of gravity
Tekno wing mount
Ofna wing
Kustom mounted VSM, I have a plate maid up that sits on top the tranny for hte VSM
Kustom radio box, I shaved revo off the top, and I cut a hole in the bottom so I could mount the Smart Temp so I could see it with the body on. Also, I have a hole cut in the back for the heat probe that goes to the engine.
Sealed electronics
I cut the manifold and extended it with a silicone air filter neck form an Integy filter that was useless.
Lunsford TI hinge pins all around
Reamed the a-arms free so they would bind less
two Stainless steal screw kits
RPM bumper
Upside down front bumper mount( puts it lower to the ground and it sits on top of my kustom skid plate)
Aluminum wheel hexes
Steering stops are cut
Extended carbon fiber center skid plate
Boca series ceramic bearings in every thing except hubs
And my set up is
60 k diff fluid
90 wt oil in front shocks, 100 in the rear. Float with 3rd hole drilled in it for more flow
2 digress toe in on the front, 1 digress toe out in the rear.
Long travel rockers and tie-rods
Lowest slot in front and middle in the rear
Bodies
1 Pro-line Chevy Silverado HD Concept, painted by Tyson Heck at Total airbrush graphics
2 Pro-line Crowd Pleazer 2.0 painted by Tyson Heck at Total Airbrush Graphics
3 Grave digger body, painted flat black by me
4 Stock body painted by Traxxas
Sirio 23 monster power engine. 2 gallons ran. Still getting stronger. Has a scratch on the cooling head. All new bearings.
Engine new, comes with two mounts
boca lightning sires bearings
__________________________
TRX 2.5r
started life as a 2.5 tmaxx engine. I rebiult it wiht all new trx 2.5r engines, never started
3 chargers for rx battarie chargers.
duratrax charger
Tsais twin exhaust pipe
spare stearing servos x3
plus ALL extram skid plates, meaning i have everything plastic stock, and i also have enver used aluminum parts i didn't use. I have original rockers, a-arms, chassis parts, and new axels. Everything i ever bought for the truck exept a few engines, and tires comes with it. I used to run a werks 4 shoe racing clutch and i would recomend it if you ever race, but they requre cleaning ALL the time i also have alot of other parts to i probaly forget stuff but any more questions email me at patfatnu@hotmail.com i got lots of pics to i jsut dont know how to upl;oad them give offers in cash or trade ide liek a stock revo 3.3 or a tmaxx 3.3 and cash